Búsqueda

MAN-00555: target database connect string must be specified ==== Cause: The TARGET parameter was not specified. Action: Supply the necessary parameter. ==== RMAN-00556: could not open CMDFILE "string" ==== C... en the file. Action: Check that the filename was specified correctly and that the file exists and that the u

ue used for export: string ==== Cause: The value specified for FILESIZE does not match the value specified d... of the export file. Action: If you believe the specified FILESIZE value is correct, verify that you specified the correct file for import. If you specified the correct file but are unsure about the correct

There is an overlap of file numbers in the files specified on the command line or the same file is specified twice. If they are not the exact same file then one is likely to be a backup of the other. If they are two members of the same log they must be specified together in a group file spec. This message will

O-01855 dimension name 'string' was not found for specified HHCODE column ==== Cause: Either the dimension name does not exist in the specified spatial table or name is incorrectly spelled. Action: Verify th... nsion name is correct or verify that it exists in specified spatial table for the specified HHCODE column. -

alacion Oracle 10g]] </columns> ==== ORA-22993: specified input amount is greater than actual source amount... the source LOB/FILE value was reached before the specified input amount was copied/loaded. Action: (1) will... nction. Modify the code either to send the amount specified or to pass 0 as the input amount so that any amou

ST or LOG_ARCHIVE_DUPLEX_DEST was in use when the specified LOG_ARCHIVE_DEST_n (n = 1...10) or DB_RECOVERY_FI... r ALTER SESSION command to define a value for the specified LOG_ARCHIVE_DEST_n or DB_RECOVERY_FILE_DEST param... CHIVE LOG START TO command was in effect when the specified LOG_ARCHIVE_DEST_n parameter was encountered whil

</columns> ==== FRM-15401: Unable to load the specified Graphics Designer (OGD) file. ==== Cause: The OGD filen specified in the Filename property of the chart item could not be found. Action: Make sure the specified OGD file exists in the specified location. ---- * [[http://www.wikioracl

ST or LOG_ARCHIVE_DUPLEX_DEST was in use when the specified LOG_ARCHIVE_DEST_n (n = 1...10) parameter was enc... r ALTER SESSION command to define a value for the specified LOG_ARCHIVE_DEST_n parameter. An ALTER SYSTEM A... CHIVE LOG START TO command was in effect when the specified LOG_ARCHIVE_DEST_n parameter was encountered whil

talacion Oracle 10g]] </columns> ==== ORA-22993 specified input amount is greater than actual source amount... the source LOB/FILE value was reached before the specified input amount was copied/loaded. Action: (1) wil... nction. Modify the code either to send the amount specified or to pass 0 as the input amount so that any amou

There is an overlap of file numbers in the files specified on the command line or the same file is specified twice. If they are not the exact same file then one is likely to be a backup of the other. If they are two members of the same log they must be specified together in a group file specification. This mess

Cause: The SQLCHECK option was entered inline and specified a level of checking higher than the level specified (or accepted by default) on the command line. This is not allowed. For example, if SQLCHECK={SYNTAX | LIMITED} is specified on the command line, SQLCHECK={SEMANTICS | FULL} cannot be specified inli

nly one ENABLE/DISABLE ROW MOVEMENT clause can be specified ==== Cause: One of three possible actions caused the error: 1) ENABLE ROW MOVEMENT was specified more than once. 2) DISABLE ROW MOVEMENT was specified more than once. 3) Both ENABLE ROW MOVEMENT and DISABLE ROW MOVEMENT were specified. Action: Re

=== Cause: The password cannot be reused for the specified number of days or for the specified number of pas... : Try the password that you have not used for the specified number of days or the specified number of passwor

</columns> ==== IMP-00085 multiple input files specified for unbounded export file ==== Cause: You specified multiple file names for the FILE parameter when doing an import, but the header in the export fi... created by an export operation in which the user specified a non-zero value for the FILESIZE parameter. Act